Mach 5 User’s Manual Revision 2.1 1
Mach 5 User’s Manual Revision 2.1 10 Range LED. Should either of these conditions occur, con
Mach 5 User’s Manual Revision 2.1 11 Figure 3, Instrument Controls Display The main contr
Mach 5 User’s Manual Revision 2.1 12 Trigger Polarity Sets the trigger edge polarity for th
Mach 5 User’s Manual Revision 2.1 13 Read 2, pulse offset = 500,001, number of pulses to ret
Mach 5 User’s Manual Revision 2.1 14 With internal triggering, if the pulse is below the tr
Mach 5 User’s Manual Revision 2.1 15 1s 68.27% 2s 95.450% 3s 99.7300% 4s 99.9
Mach 5 User’s Manual Revision 2.1 16 with wavelength, turning Wavelength Compensation on may
Mach 5 User’s Manual Revision 2.1 17 Pulse Energy (in Joules), Time Stamp (in Seconds), Pro
Mach 5 User’s Manual Revision 2.1 18 Calls a display of measured data sampled at a 10Hz rat
Mach 5 User’s Manual Revision 2.1 19 The Life Test Display Run Life Test The Life Tests V
Mach 5 User’s Manual Revision 2.1 2 WARRANTY The Gentec-EO MACH 5 Meter carries a one-year w
Mach 5 User’s Manual Revision 2.1 20 The Controls are: Start Test Starts the test with
Mach 5 User’s Manual Revision 2.1 21 The Number of pulses to measure when the instrument is
Mach 5 User’s Manual Revision 2.1 22 The selected stats will be stored, comma separated.
Mach 5 User’s Manual Revision 2.1 23 The current status of the running test sequence. Data
Mach 5 User’s Manual Revision 2.1 24 Recalls a saved instrument setup. Statistics Colors
Mach 5 User’s Manual Revision 2.1 25 initializes the GUI and the instrument based on the ins
Mach 5 User’s Manual Revision 2.1 26 Figure 4, Strip Chart Display The functions of the c
Mach 5 User’s Manual Revision 2.1 27 Place Cursor on Min Places a cursor on the minimum va
Mach 5 User’s Manual Revision 2.1 28 From the continuous period data, the true period can be
Mach 5 User’s Manual Revision 2.1 29 Figure 5, Histogram Display The functions of the co
Mach 5 User’s Manual Revision 2.1 3 SAFETY INFORMATION Do not use the MACH 5 if the device
Mach 5 User’s Manual Revision 2.1 30 Figure 6, Statistics Display The functions of the co
Mach 5 User’s Manual Revision 2.1 31 The maximum pulse energy in the data set. Mean The
Mach 5 User’s Manual Revision 2.1 32 the mode of X is 4 because that is the value that most
Mach 5 User’s Manual Revision 2.1 33 Figure 7, FFT Display The function of the controls a
Mach 5 User’s Manual Revision 2.1 34 Figure 8, Probe Data Display The functions of the co
Mach 5 User’s Manual Revision 2.1 35 The responsivity of the sensor at the calibration wave
Mach 5 User’s Manual Revision 2.1 36 The Controls are: Measured Average Power Enter the
Mach 5 User’s Manual Revision 2.1 37 After the probe EPROM is written, Mach 5 will be reset
Mach 5 User’s Manual Revision 2.1 38 Getting Ready to Measure Data The Mach 5 instrument a
Mach 5 User’s Manual Revision 2.1 39 a trigger is generated by the instrument. For external
Mach 5 User’s Manual Revision 2.1 4 Table of Contents Introduction ...
Mach 5 User’s Manual Revision 2.1 40 Note that when the instrument is set back to internal t
Mach 5 User’s Manual Revision 2.1 41 tracking had been turned on, the trigger level would ha
Mach 5 User’s Manual Revision 2.1 42 minutes of data. Pressing the ARM button again stops da
Mach 5 User’s Manual Revision 2.1 43 Missing Pulses The Mach 5 Applications software is c
Mach 5 User’s Manual Revision 2.1 44 The response of the probe is stored in the probe memory
Mach 5 User’s Manual Revision 2.1 45 Instrument Specifications Power Supp
Mach 5 User’s Manual Revision 2.1 46 Recycling and separation procedure. This section is u
Mach 5 User’s Manual Revision 2.1 47 DECLARATION OF CONFORMITY Application of Council Dire
Mach 5 User’s Manual Revision 2.1 48
Mach 5 User’s Manual Revision 2.1 5 7.8.2 Dismantling procedure: ...
Mach 5 User’s Manual Revision 2.1 6 Figure 2, Mach 5 Back Panel Installing the Software
Mach 5 User’s Manual Revision 2.1 7 3. The Found New Hardware Wizard will run. If the Windo
Mach 5 User’s Manual Revision 2.1 8 The software installation is now complete. You may now
Mach 5 User’s Manual Revision 2.1 9 The Armed LED illuminated when the unit has been armed
Comments to this Manuals